Any one got any further with the IP260 ?
My experiences so far :
I got monowall 1.236 working on it, it seems to get stuck on the bootloader, need to press CR on the console to get it to continue and boot into monowall. After this it works very well.
This is with a CF card in place of the HD and the native CF empty.
F... E... D... C... B... A... 9... 8... 7... 6... 5... 4... 3... 2... 1... 0...
Nokia Baja BIOS bootstrap loader, Version 2.02
Copyright (c) 1997-2005, Nokia, Inc.
Baja motherboard type 5981, Manu. Rev 11, Board Rev 1
CPU Id 0x06B0 stepping 4, Rev 0, L2 Cache 256KB
512MB SDRAM memory
DIMM 0 256 MBytes, Single Sided DIMM 1 256 MBytes, Single Sided
Loading kernel from BIOS_BOOT
Loading master boot sector...
Transferring control to the master bootstrap loader...
<GETS STUCK HERE - NEED TO PRESS CR>
>> FreeBSD/i386 BOOT
Default: 0:ad(0,a)/boot/loader
boot:
Console: internal video/keyboard
BIOS drive C: is disk0
BIOS 640kB/523264kB available memory
FreeBSD/i386 bootstrap loader, Revision 0.8
(
root@fb411.neon1.net, Sun May 8 12:15:29 CEST 2005)
/kernel text=0x2eeb60 data=0x69d50+0x2221c syms=[0x4+0x409a0+0x4+0x489a6]
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.11-RELEASE-p26 #0: Fri Aug 8 20:42:40 CEST 2008
root@fb411.neon1.net:/usr/src/sys/compile/M0N0WALL_GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Intel(R) Celeron(TM) CPU 400MHz (400.91-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b4 Stepping = 4
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PA
T,PSE36,MMX,FXSR,SSE>
real memory = 67502080 (65920K bytes)
avail memory = 48103424 (46976K bytes)
Preloaded elf kernel "kernel" at 0xc1106000.
Preloaded mfs_root "/mfsroot" at 0xc110609c.
Pentium Pro MTRR support enabled
md0: Preloaded image </mfsroot> 12582912 bytes at 0xc0504e1c
md1: Malloc disk
pcibios: No call entry point
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82801BA/BAM (ICH2) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pcib2: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
pci2: <PCI bus> on pcib2
pci2: <unknown card> (vendor=0x14e4, dev=0x5823) at 0.0 irq 10
pcic0: <TI PCI-1520 PCI-CardBus Bridge> mem 0x80010000-0x80010fff irq 11 at devi
ce 1.0 on pci2
pcic0: TI12XX PCI Config Reg: [pwr save][CSC serial isa irq]
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pcic1: <TI PCI-1520 PCI-CardBus Bridge> mem 0x80040000-0x80040fff irq 11 at devi
ce 1.1 on pci2
pcic1: TI12XX PCI Config Reg: [pwr save][CSC serial isa irq]
pccard1: <PC Card 16-bit bus (classic)> on pcic1
fxp0: <Intel 82559ER Embedded 10/100 Ethernet> port 0x3040-0x307f mem 0x800a0000
-0x800bffff,0x80080000-0x80080fff irq 5 at device 2.0 on pci2
fxp0: Ethernet address 00:00:00:00:00:00
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: <Intel 82559ER Embedded 10/100 Ethernet> port 0x3080-0x30bf mem 0x800e0000
-0x800fffff,0x800d0000-0x800d0fff irq 6 at device 3.0 on pci2
fxp1: Ethernet address 00:00:00:00:00:00
inphy1: <i82555 10/100 media interface> on miibus1
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp2: <Intel 82559ER Embedded 10/100 Ethernet> port 0x30c0-0x30ff mem 0x80120000
-0x8013ffff,0x80110000-0x80110fff irq 7 at device 4.0 on pci2
fxp2: Ethernet address 00:00:00:00:00:00
inphy2: <i82555 10/100 media interface> on miibus2
inphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp3: <Intel 82559ER Embedded 10/100 Ethernet> port 0x3400-0x343f mem 0x80160000
-0x8017ffff,0x80150000-0x80150fff irq 9 at device 5.0 on pci2
fxp3: Ethernet address 00:00:00:00:00:00
inphy3: <i82555 10/100 media interface> on miibus3
inphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <Intel 82801BA/BAM (ICH2) PCI to LPC bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 ATA100 controller> port 0x2000-0x200f at device 31.1 on pci
0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x2443) at 31.3 irq 9
orm0: <Option ROM> at iomem 0xe0000-0xeffff on isa0
pmtimer0 on isa0
fdc0: cannot reserve interrupt line
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
BRIDGE 020214 loaded
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.35 initialized. Default = block all, Logging = enabled
ad0: 122MB <TOSHIBA THNCF128MMA> [978/8/32] at ata0-master PIO2
Mounting root from ufs:/dev/md0c
kern.coredump: 1 -> 0
Found configuration on ad0.
Initializing timezone... done
Initializing PC cards... done
Configuring firewall... done
Configuring LAN interface... done
Configuring WAN interface... done
Configuring OPT1 (OPT1) interface... done
Configuring OPT2 (OPT2) interface... done
Starting syslog service... done
Starting webGUI... done
Starting DNS forwarder... done
Starting DHCP service... done
Starting NTP client... done
*** This is m0n0wall, version 1.236
built on Wed Sep 30 22:38:38 CEST 2009 for generic-pc
Copyright (C) 2002-2008 by Manuel Kasper. All rights reserved.
Visit
http://m0n0.ch/wall for updates.
LAN IP address: 192.168.199.253
Port configuration:
LAN -> fxp0
WAN -> fxp3
OPT1 -> fxp1 (OPT1)
OPT2 -> fxp2 (OPT2)
m0n0wall console setup
**********************
1) Interfaces: assign network ports
2) Set up LAN IP address
3) Reset webGUI password
4) Reset to factory defaults
5) Reboot system
6) Ping host
Enter a number:
Topic: IP260