Hi everyone , i am newbie to this , i buy an firebox v60L on ebay and i am trying the monowall firmware .
At first i had some problems trying to figure out witch type of cable was to get a console connection to this firewall , but now that i solve that i am stuck on the menu using hyper terminal .
i press the numbers and nothing happens .
WatchGuard Hardware Platform
PCI Device Table.
Bus Dev Func VendID DevID Class Irq
00 00 00 8086 7192 Host Bridge
00 05 00 8086 1209 Ethernet 9
00 06 00 8086 1209 Ethernet 6
00 07 00 8086 7110 ISA Bridge
00 07 01 8086 7111 IDE Controller
00 07 02 8086 7112 Serial Bus 11
00 07 03 8086 7113 PCI Bridge
00 08 00 13A3 0006 Co-Processor 10
00 09 00 1617 0101 Ethernet 11
(C) 2000 General Software, Inc.
Pentium III-4.3-6E69-2A4E
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.4-RELEASE-p11 #0: Thu Nov 1 11:01:10 CET 2012
root@mb64.neon1.net:/usr/src/sys/i386/compile/M0N0WALL_GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Pentium III (847.74-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x68a Stepping = 10
Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PA
T,PSE36,PN,MMX,FXSR,SSE>
real memory = 134217728 (128 MB)
avail memory = 105115648 (100 MB)
wlan: mac acl policy registered
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <Intel 82443BX host to PCI bridge (AGP disabled)> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
fxp0: <Intel 82559ER Embedded 10/100 Ethernet> port 0xfc00-0xfc3f mem 0xc0000000
-0xc0000fff,0xc0020000-0xc003ffff irq 9 at device 5.0 on pci0
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:01:21:b0:1c:70
fxp1: <Intel 82559ER Embedded 10/100 Ethernet> port 0xf800-0xf83f mem 0xc0040000
-0xc0040fff,0xc0060000-0xc007ffff irq 6 at device 6.0 on pci0
miibus1: <MII bus> on fxp1
inphy1: <i82555 10/100 media interface> on miibus1
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: Ethernet address: xx:xx:xx:xx:xx
isab0: <PCI-ISA bridge> at device 7.0 o pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x37
6,0xf400-0xf40f at device 7.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xf000-0xf01f irq 11 at de
vice 7.2 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge> at device 7.3 (no driver attached)
pci0: <processor> at device 8.0 (no driver attached)
pci0: <network, ethernet> at device 9.0 (no driver attached)
pmtimer0 on isa0
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: [FAST]
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
Timecounter "TSC" frequency 847739506 Hz quality 800
Timecounters tick every 1.000 msec
Fast IPsec: Initialized Security Association Processing.
IP Filter: v4.1.33 initialized. Default = block all, Logging = enabled
md0: Preloaded image </mfsroot> 16777216 bytes at 0xc0ad4dc8
ad0: 122MB <SanDisk SDCFB-128 HDX 2.15> at ata0-master PIO4
Trying to mount root from ufs:/devstray irq7
/md0
kern.coredump: 1 -> 0
Found configuration on ad0.
Initializing timezone... done
Configuring firewall... done
Configuring LAN interface... done
Configuring WAN interface... done
Starting syslog service... done
Starting webGUI... done
Starting DNS forwarder... done
Starting DHCP service... done
Starting NTP client... done
*** This is m0n0wall, version 1.34
built on Mon Nov 12 13:17:31 CET 2012 for generic-pc-serial
Copyright (C) 2002-2012 by Manuel Kasper. All rights reserved.
Visit
http://m0n0.ch/wall for updates.
LAN IP address: 192.168.1.1
Port configuration:
LAN -> sis0
WAN -> sis1
m0n0wall console setup
**********************
1) Interfaces: assign network ports
2) Set up LAN IP address
3) Reset webGUI password
4) Reset to factory defaults
5) Reboot system
6) Ping host
Enter a number:
Topic: stuck on monowall menu