Hardware

Has any tried m0n0wall on a Contivity 1010. I has sucefully installed on Contivity 100 and Contivity 1500 but in Contivty 1010 get stuck on: Configuring LAN interface... fxp0: Microcode loaded, int_delay: 1000 usec  bundle_max: 6.

See below:


Nortel BIOS version 4.3

00000640K Low Memory Passed
00129024K Ext Memory Passed
Wait.....

General Software Celeron Embedded BIOS (tm) Version 4.3
Copyright (C) 2000 General Software, Inc.

(C) 2000 General Software, Inc.
Celeron-4.3-6E69-E20E

Console: internal video/keyboard
BIOS drive C: is disk0
BIOS 638kB/129024kB available memory

FreeBSD/i386 bootstrap loader, Revision 0.8
(root@fb411.neon1.net, Sun May  8 12:15:29 CEST 2005)
/kernel text=0x2eeb60 data=0x69d50+0x2221c syms=[0x4+0x409a0+0x4+0x489a6]
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.11-RELEASE-p26 #0: Sat Jan 27 15:24:23 CET 2007
    root@fb411.neon1.net:/usr/src/sys/compile/M0N0WALL_GENERIC
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (300.68-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x665  Stepping = 5
  Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory  = 133169152 (130048K bytes)
avail memory = 112963584 (110316K bytes)
Preloaded elf kernel "kernel" at 0xc1006000.
Preloaded mfs_root "/mfsroot" at 0xc100609c.
Pentium Pro MTRR support enabled
md0: Preloaded image </mfsroot> 11534336 bytes at 0xc0504e1c
md1: Malloc disk
Using $PIR table, 8 entries at 0xc00f1bf0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82810 (i810 GMCH) Host To Hub bridge> on motherboard
pci0: <PCI bus> on pcib0
pci0: <Intel 82810 (i810 GMCH) SVGA controller> at 1.0 irq 12
pcib1: <Intel 82801AA (ICH) Hub to PCI bridge> at device 30.0 on pci0
pci1: <PCI bus> on pcib1
fxp0: <Intel 82559ER Embedded 10/100 Ethernet> port 0xee00-0xee3f mem 0xc0120000-0xc013ffff,0xc0100000-0xc0100fff irq 9
at device 0.0 on pci1
fxp0: Ethernet address 00:09:97:16:af:e4, 10Mbps
fxp1: <Intel 82559ER Embedded 10/100 Ethernet> port 0xea00-0xea3f mem 0xc0160000-0xc017ffff,0xc0140000-0xc0140fff irq 12
 at device 1.0 on pci1
fxp1: Disabling dynamic standby mode in EEPROM
fxp1: New EEPROM ID: 0xfffd
fxp1: EEPROM checksum @ 0xff: 0xffff -> 0xbbb9
fxp1: Ethernet address ff:ff:ff:ff:ff:ff, 10Mbps
isab0: <Intel 82801AA (ICH) PCI to LPC bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH ATA66 controller> port 0xfc00-0xfc0f at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82801AA (ICH) USB controller> port 0xf800-0xf81f irq 12 at device 31.2 on pci0
usb0: <Intel 82801AA (ICH) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <unknown card> (vendor=0x8086, dev=0x2413) at 31.3 irq 12
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
RTC BIOS diagnostic error 8<fixed_disk>
BRIDGE 020214 loaded
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.35 initialized.  Default = block all, Logging = enabled
ad0: 61MB <SanDisk SDCFB-64> [490/8/32] at ata0-master PIO1
Mounting root from ufs:/dev/md0c
kern.coredump: 1 -> 0
Found configuration on ad0.
Initializing timezone... done
Initializing PC cards... failed (probably no PC card controller present)
Configuring firewall... done
Configuring LAN interface... fxp0: Microcode loaded, int_delay: 1000 usec  bundle_max: 6

Looks that I had better luck with pfSense.

boot/kernel/kernel text=0x4b3c34 data=0x90494+0x42658 |

Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p5 #0: Mon Jul  2 20:37:09 EDT 2007
    sullrich@builder6.pfsense.com:/usr/obj.pfSense/usr/src/sys/pfSense_wrap.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium II/Pentium II Xeon/Celeron (300.68-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x665  Stepping = 5
  Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory  = 133169152 (127 MB)
avail memory = 120840192 (115 MB)
wlan: mac acl policy registered
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <Intel 82810 (i810 GMCH) Host To Hub bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 8 Entries> on motherboard
pci0: <PCI bus> on pcib0
$PIR: No matching entry for 0.1.INTA
$PIR: No matching entry for 0.31.INTD
$PIR: No matching entry for 0.31.INTB
pci0: <display, VGA> at device 1.0 (no driver attached)
pcib1: <PCIBIOS PCI-PCI bridge> at device 30.0 on pci0
pci1: <PCI bus> on pcib1
fxp0: <Intel 82559ER Embedded 10/100 Ethernet> port 0xee00-0xee3f mem 0xc0100000-0xc0100fff,0xc0120000-0xc013ffff irq 9
at device 0.0 on pci1
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:09:97:16:af:e4
fxp1: <Intel 82559ER Embedded 10/100 Ethernet> port 0xea00-0xea3f mem 0xc0140000-0xc0140fff,0xc0160000-0xc017ffff irq 12
 at device 1.0 on pci1
fxp1: Disabling dynamic standby mode in EEPROM
fxp1: New EEPROM ID: 0xfffd
fxp1: EEPROM checksum @ 0xff: 0xffff -> 0xbbb9
miibus1: <MII bus> on fxp1
inphy1: <i82555 10/100 media interface> on miibus1
inphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: Ethernet address: ff:ff:ff:ff:ff:ff
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH UDMA66 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
uhci0: <Intel 82801AA (ICH) USB controller> port 0xf800-0xf81f irq 12 at device 31.2 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801AA (ICH) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
RTC BIOS diagnostic error 8<fixed_disk>
Timecounter "TSC" frequency 300683821 Hz quality 800
Timecounters tick every 10.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: 123MB <LEXAR ATA FLASH V1.03> at ata0-master PIO4
GEOM_LABEL: Label for provider ad0a is ufs/pfSense.
GEOM_LABEL: Label for provider ad0d is ufs/pfSenseCfg.
Trying to mount root from ufs:/dev/ufs/pfSense

     ___
 ___/ f \
/ p \___/ Sense
\___/   \
    \___/

Welcome to pfSense 1.2-BETA-2 on the 'embedded' platform...

Setting up embedded specific environment... done.
Mounting filesystems... done.
Creating symlinks......done.
Launching PHP init system... done.
Initializing.................. done.
Starting device manager (devd)...done.
Loading configuration......done.

Network interface mismatch -- Running interface assignment option.

Valid interfaces are:

fxp0    00:09:97:16:af:e4
fxp1    ff:ff:ff:ff:ff:ff

Do you want to set up VLANs first?
If you are not going to use VLANs, or only for optional interfaces, you should
say no here and use the webConfigurator to configure VLANs later, if required.

Do you want to set up VLANs now [y|n]?

Well, well,,,,no luck at all. I tried AskoziaPBX but got:

fxp0: device timeout
fxp0: Microcode loaded, int_delay: 1000 usec  bundle_max: 6

Any clues?

Thx!

================

General Software Celeron Embedded BIOS (tm) Version 4.3
Nortel BIOS version 4.3ral Software, Inc.

Nortel Networks Contivity

00000640K Low Memory Passed
00129024K Ext Memory Passed
Wait.....

(C) 2000 General Software, Inc.
Celeron-4.3-6E69-E20E

Consoles: internal video/keyboard
BIOS drive C: is disk0
BIOS 638kB/129024kB available memory

FreeBSD/i386 bootstrap loader, Revision 1.1
(root@freebsd6.askozia.com, Wed Jun 27 15:58:46 CEST 2007)
/kernel text=0x39fcd0 data=0x8d534+0x288b0 syms=[0x4+0x4a060+0x4+0x5da96]
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p5 #0: Wed Jun 27 15:57:42 CEST 2007
    root@freebsd6.askozia.com:/usr/src/sys/i386/compile/ASKOZIAPBX_GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium II/Pentium II Xeon/Celeron (300.68-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x665  Stepping = 5
  Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory  = 133169152 (127 MB)
avail memory = 104108032 (99 MB)
kbd1 at kbdmux0
cpu0 on motherboard
pcib0: <Intel 82810 (i810 GMCH) Host To Hub bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 8 Entries> on motherboard
pci0: <PCI bus> on pcib0
$PIR: No matching entry for 0.1.INTA
$PIR: No matching entry for 0.31.INTD
$PIR: No matching entry for 0.31.INTB
pci0: <display, VGA> at device 1.0 (no driver attached)
pcib1: <PCIBIOS PCI-PCI bridge> at device 30.0 on pci0
pci1: <PCI bus> on pcib1
fxp0: <Intel 82559ER Embedded 10/100 Ethernet> port 0xee00-0xee3f mem 0xc0100000-0xc0100fff,0xc0120000-0xc013ffff irq 9
at device 0.0 on pci1
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:09:97:16:af:e4
fxp1: <Intel 82559ER Embedded 10/100 Ethernet> port 0xea00-0xea3f mem 0xc0140000-0xc0140fff,0xc0160000-0xc017ffff irq 12
 at device 1.0 on pci1
fxp1: Disabling dynamic standby mode in EEPROM
fxp1: New EEPROM ID: 0xfffd
fxp1: EEPROM checksum @ 0xff: 0xffff -> 0xbbb9
miibus1: <MII bus> on fxp1
inphy1: <i82555 10/100 media interface> on miibus1
inphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: Ethernet address: ff:ff:ff:ff:ff:ff
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH UDMA66 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
uhci0: <Intel 82801AA (ICH) USB controller> port 0xf800-0xf81f irq 12 at device 31.2 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801AA (ICH) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
RTC BIOS diagnostic error 8<fixed_disk>
Timecounter "TSC" frequency 300684260 Hz quality 800
Timecounters tick every 1.000 msec
md0: Preloaded image </mfsroot> 16713728 bytes at 0xc08fe5c4
ad0: FAILURE - SETFEATURES SET TRANSFER MODE status=51<READY,DSC,ERROR> error=4<ABORTED>
ad0: 46MB <Hitachi CV 7.1.1 Rev 1.01> at ata0-master BIOSPIO
Trying to mount root from ufs:/dev/md0
Found configuration on ad0.
Initializing timezone... done
Configuring LAN interface... fxp0: Microcode loaded, int_delay: 1000 usec  bundle_max: 6
Interrupt storm detected on "irq12:"; throttling interrupt source
fxp0: link state changed to UP
done
Starting syslog service... done
Starting webGUI... done
Starting NTP client... done
Starting Asterisk...
 - loading zaptel
Zapata Telephony Interface Registered on major 196
Echo Canceller: MG2
 - loading ztdummy
ztdummy: loaded
 - generating sip configuration...done
 - generating iax configuration...done
 - generating conferencing configuration...done
 - generating dialplan...done
 - generating voicemail configuration...done
 - executing Asterisk...done
 - increasing verbosity...done
done


*** This is AskoziaPBX, version pb6
    built on Thu Jul 5 09:42:17 CEST 2007 for generic-pc
    Copyright (C) 2007 IKT. All rights reserved.
     m0n0wall is Copyright (C) 2002-2006 Manuel Kasper all rights reserved.
    Visit http://askozia.com/pbx for updates.

    LAN IP address: 192.168.1.2 on fxp0

AskoziaPBX console setup
**********************
1) Interfaces: assign network port
2) Set up LAN IP address
3) Reset webGUI password
4) Reset to factory defaults
5) Reboot system
6) Ping host
7) Asterisk Console

Enter a number:

fxp0: device timeout
fxp0: Microcode loaded, int_delay: 1000 usec  bundle_max: 6
fxp0: device timeout
fxp0: Microcode loaded, int_delay: 1000 usec  bundle_max: 6
fxp0: device timeout
fxp0: Microcode loaded, int_delay: 1000 usec  bundle_max: 6
fxp0: device timeout
fxp0: Microcode loaded, int_delay: 1000 usec  bundle_max: 6
fxp0: device timeout
fxp0: Microcode loaded, int_delay: 1000 usec  bundle_max: 6
fxp0: device timeout
fxp0: Microcode loaded, int_delay: 1000 usec  bundle_max: 6
fxp0: device timeout
fxp0: Microcode loaded, int_delay: 1000 usec  bundle_max: 6
fxp0: device timeou

If pfsense works, m0n0wall 1.3b2 should as well. See the Beta page on the site.

Bumping this up a bit! I have a Contivity 1010 that I am having some trouble with.

I can get the image on the flash card OK and it boots no problems. But when I go to configure the ethernet ports the WAN port (fxp0) has "ff:ff:ff:ff:ff:ff" as a MAC address. I did some googling and found where the spoofmac tag has been used in the past so I tried that without success.

I am using generic-pc-serial-1.33.img

Any other ideas???

thanks!!!

Damo.