Hardware

Team

I am upgrading my Nokia IP120 to monowall 1.3....but it give the following error:

Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p6 #0: Sun Jul 29 21:28:28 CEST 2007
    root@mb62.neon1.net:/usr/src/sys/i386/compile/M0N0WALL_GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (266.68-MHz 586-class CPU)
  Origin = "Geode by NSC"  Id = 0x540  Stepping = 0
  Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory  = 134217728 (128 MB)
avail memory = 105140224 (100 MB)
wlan: mac acl policy registered
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 3 Entries> on motherboard
pci0: <PCI bus> on pcib0


Fatal trap 12: page fault while in kernel mode
fault virtual address   = 0xeb11f
fault code              = supervisor read, page not present
instruction pointer     = 0x20:0xc00eb621
stack pointer           = 0x28:0xc1c20a54
frame pointer           = 0x28:0xc1c20a54
code segment            = base 0x0, limit 0xfffff, type 0x1b
                        = DPL 0, pres 1, def32 1, gran 1
processor eflags        = interrupt enabled, resume, IOPL = 0
current process         = 0 (swapper)
trap number             = 12
panic: page fault
Uptime: 1s
Automatic reboot in 15 seconds - press a key on the console to abort
Rebooting...

=========================================

With monowall 1.22, I dont have any issue, see below:


Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.11-RELEASE-p16 #0: Sun Apr  2 09:52:18 CEST 2006
    root@fb411.neon1.net:/usr/src/sys/compile/M0N0WALL_GENERIC
Timecounter "i8254"  frequency 1193182 Hz
CPU: NSC Geode (266.68-MHz 586-class CPU)
  Origin = "Geode by NSC"  Id = 0x540  Stepping = 0  DIR=0x8247
  Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory  = 134217728 (131072K bytes)
avail memory = 113995776 (111324K bytes)
Preloaded elf kernel "kernel" at 0xc1006000.
Preloaded mfs_root "/mfsroot" at 0xc100609c.
md0: Preloaded image </mfsroot> 11534336 bytes at 0xc0504e1c
md1: Malloc disk
Using $PIR table, 3 entries at 0xc00f4fb0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
fxp0: <Intel 82559ER Embedded 10/100 Ethernet> port 0x8000-0x803f mem 0x80100000-0x8011ffff,0x80000000-0x80000fff irq 11
 at device 14.0 on pci0
fxp0: Ethernet address 00:00:8e:21:00:00
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: <Intel 82559ER Embedded 10/100 Ethernet> port 0x8400-0x843f mem 0x80300000-0x8031ffff,0x80200000-0x80200fff irq 10
 at device 15.0 on pci0
fxp1: Ethernet address 00:00:8e:21:00:00
inphy1: <i82555 10/100 media interface> on miibus1
inphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp2: <Intel 82559ER Embedded 10/100 Ethernet> port 0x8800-0x883f mem 0x80500000-0x8051ffff,0x80400000-0x80400fff irq 5
at device 16.0 on pci0
fxp2: Ethernet address 00:00:8e:21:00:00
inphy2: <i82555 10/100 media interface> on miibus2
inphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <Cyrix Cx5530 PCI-ISA bridge> at device 18.0 on pci0
isa0: <ISA bus> on isab0
chip1: <PCI to Other bridge (vendor=1078 device=0101)> mem 0x40012000-0x400120ff at device 18.1 on pci0
atapci0: <Cyrix 5530 ATA33 controller> port 0xfc00-0xfc0f at device 18.2 on pci0
atapci0: Busmastering DMA not supported
pci0: <unknown card> (vendor=0x1078, dev=0x0103) at 18.3
orm0: <Option ROMs> at iomem 0xe8000-0xebfff,0xec000-0xeffff on isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
BRIDGE 020214 loaded
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.35 initialized.  Default = block all, Logging = enabled
ad0: 61MB <SanDisk SDCFB-64> [490/8/32] at ata0-master BIOSPIO
Mounting root from ufs:/dev/md0c
Found configuration on ad0.
Initializing timezone... done
Initializing PC cards... failed (probably no PC card controller present)
Configuring firewall... done
Configuring LAN interface... fxp0: Microcode loaded, int_delay: 1000 usec  bundle_max: 6
done
Configuring WAN interface... done
Configuring OPT1 (OPT1) interface... done
Starting syslog service... done
Starting webGUI... done
Starting DNS forwarder... done
Starting DHCP service... done
Starting NTP client... done


*** This is m0n0wall, version 1.22
    built on Sun Apr  2 18:57:20 CEST 2006 for generic-pc
    Copyright (C) 2002-2006 by Manuel Kasper. All rights reserved.
    Visit http://m0n0.ch/wall for updates.


    LAN IP address: 192.168.1.1

    Port configuration:

    LAN   -> fxp0
    WAN   -> fxp1
    OPT1  -> fxp2 (OPT1)


m0n0wall console setup
**********************
1) Interfaces: assign network ports
2) Set up LAN IP address
3) Reset webGUI password
4) Reset to factory defaults
5) Reboot system
6) Ping host

Enter a number:

Any Clues??? Thx.

Known issue. FreeBSD problem that nobody has attempted to track down yet (I plan to eventually...).

Known issue. FreeBSD problem that nobody has attempted to track down yet (I plan to eventually...).

This would be excellent. I have some nice hardware I could use for MW. I'd help figuring this out but I don't have the "mad skills" for that  . Of course I can do something, if need be.

Not sure if this will give you some clues (see boot log below) but latest Juniper Junos (JUNOS 8.3R2. runs well on Nokia IP120. Also if Junos could not derive MAC address from EEPROM it will generate a valid ones. I am not sure if they run FreeBSD 5 or up in recent JUNOS Version.

=========================

Console: serial port
BIOS drive C: is disk0
BIOS 639kB/130048kB available memory

FreeBSD/i386 bootstrap loader, Revision 0.8
(builder@vasuki.juniper.net, Sat Jul  7 00:06:05 GMT 2007)
Loading /boot/defaults/loader.conf
/kernel text=0x4ef6eb data=0x3e928+0x59556 syms=[0x4+0x612b0+0x4+0x6dd81]

Hit [Enter] to boot immediately, or space bar for command prompt.
Booting [kernel]...

Olive CPU
Copyright (c) 1996-2007, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.

JUNOS 8.3R2.8 #0: 2007-07-07 00:23:06 UTC
    builder@vasuki.juniper.net:/build/vasuki-c/8.3R2.8/obj-i386/sys/compile/JUNIPER

Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 266676907 Hz

CPU: Pentium (266.68-MHz 586-class CPU)
  Origin = "Geode by NSC"  Id = 0x540
real memory  = 134217728 (131072K bytes)

sio0: gdb debugging port
avail memory = 122626048 (119752K bytes)
Preloaded elf kernel "kernel" at 0xc0759000.
DEVFS: ready for devices
md0: Malloc disk
Using $PIR table, 3 entries at 0xc00f4fb0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0

fxp0: <Intel Embedded 10/100 Ethernet> port 0x8000-0x803f mem 0x80100000-0x8011ffff,0x80000000-0x80000fff irq 11 at device 14.0 on pci0
fxp1: <Intel Embedded 10/100 Ethernet> port 0x8400-0x843f mem 0x80300000-0x8031ffff,0x80200000-0x80200fff irq 10 at device 15.0 on pci0
fxp2: <Intel Embedded 10/100 Ethernet> port 0x8800-0x883f mem 0x80500000-0x8051ffff,0x80400000-0x80400fff irq 5 at device 16.0 on pci0

isab0: <Cyrix Cx5530 PCI-ISA bridge> at device 18.0 on pci0
isa0: <ISA bus> on isab0
chip1: <PCI to Other bridge (vendor=1078 device=0101)> mem 0x40012000-0x400120ff at device 18.1 on pci0
atapci0: <Cyrix 5530 ATA33 controller> port 0xfc00-0xfc0f at device 18.2 on pci0
atapci0: Busmastering DMA not supported
pci0: <unknown card> (vendor=0x1078, dev=0x0103) at 18.3
orm0: <Option ROMs> at iomem 0xe8000-0xebfff,0xec000-0xeffff on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x90 on isa0
sio0: type 16550A, console
sio1: configured irq 5 not in bitmap of probed irqs 0
sio2 at port 0x2f8-0x2ff irq 3 on isa0
sio2: type 16550A
sio3: configured irq 7 not in bitmap of probed irqs 0

fxp: Could not derive MAC address from EEPROM
fxp0: Ethernet address 02:00:02:00:00:04
fxp: Could not derive MAC address from EEPROM
fxp1: Ethernet address 02:00:03:00:00:04
fxp: Could not derive MAC address from EEPROM
fxp2: Ethernet address 02:00:04:00:00:04

DEVFS: ready to run
if_pfe_ls_alloc_bdl_cb_list: Initializing bundle control block list.
ad0: 5729MB <IBM-DARA-206000> [12416/15/63] at ata0-master BIOSPIO
Mounting root from ufs:/dev/ad0s1a
if_pfe_open: listener socket opened, listening...
Mounted jbase package on /dev/vn0...
Verified manifest signed by PackageProduction_8_3_0
Verified jboot signed by PackageProduction_8_3_0
Mounted jkernel package on /dev/vn1...
veriexec pid 38 syscall 59 ran for 581.376 ms
Verified manifest signed by PackageProduction_8_3_0
Mounted jpfe package on /dev/vn2...
Mounted jdocs package on /dev/vn3...
Verified manifest signed by PackageProduction_8_3_0
Mounted jroute package on /dev/vn4...
Verified manifest signed by PackageProduction_8_3_0
Mounted jcrypto package on /dev/vn5...
Verified manifest signed by PackageProduction_8_3_0
Mounted jpfe-common package on /dev/vn6...
Mounted jweb package on /dev/vn7...
Verified manifest signed by PackageProduction_8_3_0
Executing /packages/mnt/jweb-8.3R2.8/mount.post..
Warning: Block size restricts cylinders per group to 23.
Warning: Block size restricts cylinders per group to 26.
Warning: Block size restricts cylinders per group to 27.
Warning: Block size restricts cylinders per group to 26.
swapon: adding /dev/ad0s1b as swap device
Automatic reboot in progress...
/dev/ad0s1a: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1a: clean, 51254 free /dev/ad0s1e: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1e: clean, 12112 free (14 frags, 6405 blocks, 0.0% fragmentation)
(16 frags, 1512 blocks, 0.1% fragmentation)
(14 frags, 6405 blocks, 0.0% fragmentation)
/dev/ad0s1f: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1f: clean, 3954281 free (553 frags, 494216 blocks, 0.0% fragmentation)
tunefs: soft updates set
Creating initial configuration...mgd pid 2759 syscall 59 ran for 1260.400 ms
mgd pid 2759 syscall 5 ran for 1640.143 ms
mgd pid 2759 syscall 5 ran for 1666.349 ms
mgd pid 2759 syscall 5 ran for 1033.867 ms
syncer pid 7 ran for 734.533 ms
mgd pid 2759 syscall 36 ran for 522.512 ms
rpd pid 2774 syscall 59 ran for 5800.485 ms
chassisd pid 2776 syscall 5 ran for 4156.501 ms
chassisd pid 2776 syscall 5 ran for 540.433 ms
mgd: commit complete
Setting initial options:  debugger_on_panic=NO debugger_on_break=NO.
Doing initial network setup:.
Initial interface configuration:
additional daemons:.
checking for core dump...
savecore: Router rebooting after a normal shutdown....
Additional routing options: ipsec kld.
Doing additional network setup:.
Starting final network daemons:.
setting ldconfig path: /usr/lib /opt/lib
starting standard daemons: cron.
Initial rc.i386 initialization: microcode kld.
Local package initialization:.
kern.securelevel: -1 -> 1
starting local daemons:.
Mon Aug 20 16:46:59 UTC 2007

olive-2 (ttyd0)

login: root
Password:

--- JUNOS 8.3R2.8 built 2007-07-07 00:23:06 UTC
root@olive-2% cli
root@olive-2>

Known issue. FreeBSD problem that nobody has attempted to track down yet (I plan to eventually...).

While I doubt this is a high priority, I'd love to see a solution here as well, as I am in need of NAT-T capabilities on my Nokia IP110. Please let me know if/how I can be of assistance in this process.

Cheers,
-dr.k

Has the issue been adressed in the latest beta release?

I just posted a fix for this issue.  It requires patching the FreeBSD kernel and rebuilding it.

http://forum.m0n0.ch/index.php/topic,1384.0.html

- Bruce